Performance Series’ 1050ATC, 1350ATC

Feeder Section:

1. Three lifts up and four forwarding sucker heads with angle adjustment to handle different kinds of materials.
2. Preloading device with rail cart and scaled gate.
3. Motorized side adjustment of pallet table.
4. Non-stop feeder with automatic pile lift.
5. Side blowers adjustable according to sheet size for smooth feeding, especially for thin paper transport.

Feeding Table:

1. Left and right-side push lays to ensure accurate alignment and power registration.
2. Synchronizing device to adjust the sheet positioning to the front lay by hand during production.
3. Four individually adjustable front lays at the operation side of the machine.
4. Electrical mechanical double sheet detector.
5. Sheet hold-down device (guiding the sheets to the front lays) pull and push convertible side lays (OS and OOS) with photo sensor sheet arrival control.
   
   

Die-Cutting Section:

1. Pressure-containing member adopts high-strength nodular cast iron-QT600 and special casting process, thus it has high strength and never deforms.
2. The Ni-Cr-Mo metal steel crank shaft through the special craft processing, imported from Germany.
3. Super wear-resistant worm and gear imported from Taiwan.
4. High-precision 240-degree intermittent mechanism from Taiwan.
5. Pneumatic locking device, safe and fast.
6. Double cam driven gripper opener and front lay swing frame without position restore
7. High-speed rotary joint from Italy.
8. Adopt advanced Germany siemens motor, to increase the die cutting speed to 7500 sheets/hour.
9. Die cutting plate frame, adopting central positioning system.
10. 4-inchcolour screen, displaying the working state of machine all the time.

Hot Foil Stamping Section:

1. Man-machine interactive touch function, can set different long pull and short pull.
2. The alarm will be triggered when the foil is shorter than 6cm.
3. Comprehensive foil feeding system, can realized longitudinal and lateral hot foil stamping at the same time, reducing the foil usage and saving foil replaced time.
4. Three sets of longitudinal foil advancing shafts and two sets of lateral foil advancing shafts are driven by servo motors individually programmable for short and long foil stepping.
5. Foil feeding devices are controlled by servo motor and siemens plc control system.
6. Foil breaking control.
7. Tension roller and foil advancing rollers each driven servo motors and controlled by the foil control system, new pressing roller on tension roller with easy pressure adjustment hence quick set up.
8. Foil control, such as foil advancing step combination setting, automatic most efficient stepping combination calculation as well as motion stepping combination simulation and, hologram stamping is of the latest technology the foil control system and provides reliable and precision foil advancing control.
9. Waste foil rewinding unit outside the delivery section controlled by the foil control system for efficient waste foil rejection and keeping foil tension constant by synchronizing the waste foil pulling with foil advancing.

Programmed Precision Adjustment System:

1. Available only in MHK series.
2. It adopts two individual servos to control the gripper stopper in order to adjust the precision of each gripper bar by input value in HMI, which is more operator friendly and easier to maintain the precision.

Stripping Section:

1. Foil feeding section can be replaced by stripping section for stripping use.
2. Triple action movement of the upper and lower stripping frames with lower spring-loaded stripping pins.
3. Motorized upper frame suspending hoister.
4. Upper and lower stripping tool mounting frame can be pulled out for job set up and make ready.
5. Adopt central positioning device that matched with the die cutting part to reduce the plate replacing time.

Delivery Section:

1. Automatic paper aligning device and two blowers for paper collection can ensure neat collection of thin and thick papers.
2. Automatic delivery with non – stop curtain. This curtain moves into the delivery to catch the arriving sheets during the pile exchange.
3. Gripper edge stripping and removing system with conveyor belt to remove the gripper edge waste sideways to the drive side.

Electrical Control Section:

1. Adopts electrical components of world-famous brands for better performance and in time and local after-sale-service and maintenance.
2. Twelve PLC-controlled heating zones, can be adjusted individually according to products requirement.